ImageMASSter 4008 Drive Duplicator Kit (1-to-8 Drives)

The ImageMASSter 4008 hard drive duplicator provides the tools necessary to mass duplicate today’s regular and notebook* P-ATA and S-ATA** hard drives for high volume drive duplication. Copy data only, image master hard drive sector by sector, clone data of specific sectors. Duplicate to 8 target hard drives simultaneously at speeds greater than 2GB/min.

*Requires optional notebook (2.5") adapter
**Requires optional S-ATA adapters

.: Supply Voltage: 100-240V 50/60 Hz Universal Auto switching input voltage
.: Power Consumption: 200W
.: Operating Temperature: 5°–55° C
.: Relative Humidity: 20%–60% non-condensing
.: Net Weight: 9.5lbs without drive
.: Dimensions of Unit: 13.3" x 12.1" x 4.4”

Optional Software
.: MultiMASSter: The MultiMASSter option provides the user with the ability to store multiple “software loads” to a single drive.  The user can then select and copy individual “software loads” from the MultiMASSter drive.  Depending on drive space, up to 24 loads can be stored on a single MultiMASSter drive. 
.: Host Protected Area (HPA) Option: HPA is defined as a reserved area for data storage outside the normal operating file system.  This area is hidden from the operating system and file system and is normally used for specialized applications.  Systems may wish to store configuration data or save memory to the hard disk drive device in a location that the operating systems cannot change.  If an HPA area exists on a source drive, the IM4000i copy operation will configure the target drives with a similar HPA area.
.: Device Configuration Overlay (DCO) Option: DCO allows systems to modify the apparent features provided by a hard disk drive device.  DCO provides a set of commands that allows a utility or program to modify some of the modes, commands and feature sets supported by the hard disk drive.  DCO can be used to hide and protect a portion of the drive’s area from the operating system and file system.  If DCO is detected on the source drive, the IM4000i copy operation will configure the target drives with similar DCO settings.
.: Format FAT32 Option: The FORMAT FAT32 Option provides the capability of performing a quick FAT32 format on multiple drives.   The operation creates a non-active FAT32 primary DOS partition on the drive(s) connected.
.: Linux IQ Copy Option: The Linux-IQCopy Option adds IQCopy support for the Linux Extended 2 (EXT2) and Extended 3 (EXT3) File Systems. The Linux Extended 2 and Extended 3 (EXT2/EXT3)

Optional Hardware
.: Serial-ATA Adapters: Single Channel and Multi-Channel S-ATA adapters are available to support copying S-ATA drives.  The 9 Channel S-ATA adapter will covert all ports of the IM4000i for S-ATA usage.  The Single Channel S-ATA adapters allow copying between P-ATA and S-ATA drives.
.: Notebook Adapters: ICS proprietary Notebook Adapters enables the IM4000i to support a variety of Notebook models that use a proprietary Notebook drive interface.  Adapters available include adapters for the IBM Think-Pad, Compaq Armada, NEC Versa, Dell Latitude, and Toshiba Tecra.  The ICS Standard 2.5” adapter supports all Notebook drives which do not have a proprietary interface or have been removed from their proprietary enclosures.  An ICS proprietary adapter is also available for the 1.8” ATA drive interface.
.: CF Adapter: The Flash adapter was designed to support 50-pin micro-drive devices. 
.: Shelf Solution: This Shelf Solution provides the ImageMASSter 4008i user with an alternative method to mount nine drives to the unit.  The standard tray format requires the drives to be mounted vertically, while the Shelf Solution allows the drives to be mounted in the traditional horizontal position.
.: Micro S-ATA  3.3V, 1.8" adapter
.: 9 Channel Flash Card Adapter: Allows copying to or from 50-pin ATA compatible CompactFlash (CF) cards, including Microdrives, using the ICS IM4008i duplicator.
.: Drive Cooler Solution: Reduces the heat generated by the hard drives and maintain a comfortable operating temperature.
.: eSATA: Supports eSATA drives with the purchase of an IDE-to-SATA adapter and this SATA-to-eSATA data cable
.: 3.3V Adapter: The ICS S-ATA 3.3V Adapter provides the IM400i units support for 3.3V devices which use the S-ATA interface.